#PREDATOR CNC SIMULATOR HOW TO#
#PREDATOR CNC SIMULATOR MANUAL#
#PREDATOR CNC SIMULATOR SOFTWARE#

You get to see the coordinates on the various axes, as well as the spindleвЂ™s status, the feedrate, the current tool, how long the program is predicted to take to execute to this point, and the status of coolant. This is similar to the information provided by your machineвЂ™s controller. GWE provides an instrument cluster directly under the backplot that provides information about what the g-code is doing in addition to what you see on the backplot: GWE will remember the last speed selected when you exit. The numeric speed control accepts a number from 1 to 100% execution speed. Click the Tortoise to slow way down, or click the Hare to speed up to 100%. The Tortoise, Hare, and Percent between them control the g-code playback speed. TheyвЂ™re your tools for controlling the execution of the g-code so you can see how the program works. вЂ“ Single Block: Activates Single Block mode where execution is paused after each block as though Feed Hold were pressed.ДЄs you can see, these controls are the same as youвЂ™ll find on most machine control panels. вЂ“ Feed Hold: Stop execution at the conclusion of the current block. вЂ“ Cycle Start 5 Step: Same as Cycle Start, except if Single Block is in effect, each press executes 5 blocks. If Single Block is in effect, each press executes 1 block. вЂ“ Rewind: Rewind to the beginning (first block) of the g-code program.

There is a tool tip that pops up to describe the buttonвЂ™s function: Take a minute to run your mouse cursor over each button.

#PREDATOR CNC SIMULATOR HOW TO#

Note the underline of the Rewind button to remind you how to start CNC Simulator ModeвЂ¦ In Edit Mode, G-Wizard places a subtle underline that appears by the rewind to remind you this is how to start CNC Simulator Mode: The easiest way to transition from normal editing mode to CNC Simulator Mode is to press the rewind button on the Simulator Control Buttons on the toolbar: The visibility and color of individual tools may be controlled from the Tools tabвЂ¦ The visibility and color of backplot for individual tools may be controlled via the Tool tab: Options for Backplotting Individual Tools The checkbox allows you to turn off auto-refresh even for files smaller than the maximum size. You can also press the F9 key to cause a refresh.

#PREDATOR CNC SIMULATOR MANUAL#

Files larger than this size require manual refresh by pressing the refresh button on the Toolbar or by menu pick. You can set the maximum file size that will auto-refresh after any change. The Refresh tab contains the options that control how often the Backplot is replotted: вЂ“ Reference Position Moves: This option controls whether reference moves, triggered by G27 to g30, will be plotted.

This option controls whether the extent box should be shown all the time. вЂ“ Feed Extent Box: GWE will show an extent box when you attempt to rotate or pan a complex backplot. вЂ“ Feed Moves: This option toggles whether non-G0 moves are displayed, and if so, controls the line weight used to draw them. вЂ“ Rapids Moves: This option toggles whether G0 moves are shown or not.

вЂ“ Endpoints: This options displays the endpoints of each segment with a marker so it is easier to see where segments begin or end. вЂ“ Trident: The trident that shows which direction X, Y, and Z grow larger (positive) may be turned on or off, and it can be displayed in the lower left of the backplot or always at work 0, 0, 0. вЂ“ Tool: The simulated 3D tool and holder may be turned on or off. вЂ“ Grid: The grid that provides a reference may be turned on or off. You have the ability to control visibility of the following by turning the check boxes on or off: The first is for the вЂњShowвЂќ options that control which elements are displayed in the Backplot: TheyвЂ™re accessed from the Backplot menu, and there are two tabs on the popup. G-Wizard G-Code Editor Simulator Mode: A G-Code DebuggerвЂ¦Д«efore we get into Simulator Mode, letвЂ™s describe the Backplot Options that are available. When that mode is operational, the GWE screen will display simulator information directly below the backplot, like this: We call that вЂњSimulator ModeвЂќ or вЂњDebugger ModeвЂќ, because it is intended to help you understand and debug the execution of your g-code. However, when we refer to the вЂњSimulatorвЂќ, we generally mean to refer to the running of the CNC Simulator step by step. It is operational in some form or fashion all the time, as the backplot is always available.

#PREDATOR CNC SIMULATOR SOFTWARE#

The G-Wizard EditorвЂ™s CNC SimulatorВ is the portion of the software that understands how to execute g-code and can present the backplot as well as debugging information. G-Wizard Editor: CNC Simulator and Backplotter

Predator cnc simulator